Equipment features
1. AOI, closer to the human visual mechanism.
2. Complete line inspection parameters and strong core defect detection ability.
3. It is equipped with many kinds of parameter detection logic ensure no leak detection.
4. Ultra strong error correction: Plate deformation, plate warping aligning mode.
5. The entire board can be divided into important regions, which correspond to small routes and peripheral regions, and non-important regions. Different judgment standards are adopted for important regions and non-important regions. Make sure that less false points can be reported when there is no leak detection.
6. In the linear corner, because some CAM data have sharp corners, but the actual line corners are often smoother than CAM data corners, false points may be reported. However, if the corners are not detected, gaps and convex copper leakage may appear near the corner. Long Sword AOI can make special analysis of straight corners and introduce unique detection logic to avoid false points.
7. Three drilling cover modes: Cover drilling holes out of tolerance, cover hole breakout, drill holes and cover open circuits. In response to detection requirements of different customers and different boards to drilling holes, false points of plate with bad drilling shall be reduced so as to reduce VRS workload and improve productivity.
Equipment specifications Long Sword II-750A |
|
Inspection capabilities |
|
Testing capability | Optimum test capability: 3mil (line width; line spacing); ultimate test capability: 2mil (line width; line spacing) |
Check thickness of board | 0.01 ~8mm |
Scanning efficiency (18"×24") | 4mil 240 faces/hour 3mil 220 faces/hour 2mil 150 faces/hour |
Inspection area |
|
Maximum size of working table (X*Y) | 26"X28" (680X730mm) |
Location way | Automatic positioning by plate edge without drilling |
table-board drive mode | Driven by precising lead screw and servo motor |
Inspection scope |
|
Form of board surface | Inner/outer layer; wiring types include signal lines, power ground lines, hybrid shielding, grids and others |
Base material | Electro-coppering panel; aluminum substrate; gold-plated board; dry film/wet film plate, FR-4, CEM and flexible printed circuits. |
Defect inspection | Short circuit, open circuit, line width line spacing are out of tolerance; gap, convex copper, concave copper, pinhole, residual copper, lack of holes, hole blocking, broken hole, lack of copper, wrong size and position. |
Approval of defects | Approved by inspection station |
Software system |
|
Operation interface | Support Chinese and English |
Processing software | E-Sight AOI 3200 software |
CAM data format | RS-274X GERBER format |
Working environment |
|
Temperature | 16℃～25℃ |
Humidity | 40%～60% (Non-Condensing) |
Light source |
|
Type of light source | Patent technology, AOI special LED light source, high bright life service |
Light source service life | Over 10000 hours |
Light source power | 200W |
Energy consumption |
|
Air source | 6～8Kg.f/cm2 |
Power supply | AC 380V±5% 50Hz 3.7KWh Three-phase five little system |
Energy consumption of the whole machine | 1700W |
Volume |
|
Size | L×W×H 2050mm×1320mm×1770mm |
Quality | About 1500 kgs |
Long Sword II-450
Inspection capability |
|
Testing capability | Optimal testing capability: 1.8mil (line width; line spacing); Ultimate testing capability: 1.2mil (line width; line spacing) |
Check the thickness of board | 0.01 ~8mm |
Scanning efficiency (250"×320") | 2mil 240 faces/hour 1.8mil 210 faces/hour 1.5mil 180 faces/hour |
Inspection area |
|
Maximum size of the working table (X*Y) | 13"X17" (352X450mm) |
Location way | Automatic positioning by plate edge without drilling |
Table-board drive mode | Driven by precising lead screw and servo motor |
Scope of inspection |
|
Board form | Inner/outer layer; wiring types include signal lines, power ground lines, hybrid shielding, grids and others |
Base material | Flexible circuit board and HDI board |
Defect inspection | Short circuit, open circuit, line width line spacing are out of tolerance; gap, convex copper, concave copper, pinhole, residual copper, lack of holes, hole blocking, broken hole, lack of copper, wrong size and position. |
Approval of defects | Approved by inspection station |
Software system |
|
Operation interface | Support Chinese and English |
Processing software | E-Sight AOI 3200 software |
CAM data format | RS-274X GERBER, ODB++ format |
Working environment |
|
Temperature | 16℃～25℃ |
Humidity | 40%～60% (Non-Condensing) |
Light source |
|
Type of light source | Patent technology, AOI special LED light source, high bright life service |
Light source service life | Over 10000 hours |
Light source power | 200W |
Energy consumption |
|
Air source | 6～8Kg.f/cm2 |
Power supply | AC 380V±5% 50Hz 3.7KWh Three-phase five little system |
Energy consumption of the whole machine | 1700W |
Volume |
|
Size | L×W×H 1910mm×1410mm×1820mm |
Quality | About 1200kg |